manualshive.com logo in svg

Advantech-DLoG TREK-572, User Manual

Share
Download
Advantech-DLoG TREK-572 User Manual Download Page 65

41

TREK-570/303 User Manual

 

 

 

System Menu

 

•

 

TREK V3 Watch Dog Sample Code as below figure 

 

1. 

Library Version 

2. 

Range of Watch Dog timer 

3. 

Set/Get Watch Dog time 

4. 

Enable Watch Dog timer 

5. 

Reload the watchdog timer to prevent the system from rebooting 

Testing Watch Dog

 

1. 

Opening "TREK_V3_Sample_Code_Watch_Dog.exe" 

2. 

Press "Get Range" button to check the range of watch dog timer 

3. 

Input the time which you want system keep alive. For example 1 minute as below figure 

 

 

4. 

Press "Start WD Timer" to enable watch dog timer 

5. 

Press "Trigger timer" to tell the watch dog system still alive 

6. 

If system not trigger watch dog in the setting time, you should see the system automotive 
reboot 

 

CAUTION

: This demonstration may reboot your system, if you enable watch dog 

timer and not trigger watch dog timer in time. 

 
 
Peripheral Control Demo Program 

TREK V3 Peripheral Control Sample Code is demonstration of controlling 
peripheral power. 

Summary of Contents for TREK-572











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands