Advantech-DLoG TREK-572 User Manual Download Page 28 | Manualshive

Page: 28 / 74

background image

TREK-572 /303 User Manual

12

3.1 Overview

of

Hardware

Installation

&

Upgrading

The In-Vehicle Computing Box consists of a PC-based computer
that is housed in a ruggedized aluminum enclosure. Any
maintenance or hardware upgrades can be completed after
removing the bottom cover plate.

Warning!

Do not remove the ruggedized aluminum covers until

verifying that no power is flowing within the computer.
Power must be switched off and the power cord must
be unplugged. Take care in order to avoid injury or
damage to the equipment.

3.2 Installing

the

Storage

Device

and

Memory

The In-Vehicle Computing Box can only use a mSATA as a storage
device. Put the mSATA into the slot and insert the RAM into the
200-pin SODIMM socket on the main board.

3.3 Installing

Optional

Accessories

Optional accessories, like RAM mount kits or other functional
modules are available for purchase to complement TREK-572. The
following are instructions for accessory installation.

3.3.1 Installing

TREK-572

Peripheral

Modules

There are 4 screws on the bottom of TREK-572, if you want to install
the peripherals in TREK-572, please use M2 type screw to open the
system.

`

«
...
26
27
28
29
30
...
»

Summary of Contents for TREK-572











































































Reviews:

No comments

Related manuals for TREK-572

Brand: Yawarra Pages: 4

PC 300GL Type 6267

Brand: IBM Pages: 58

Brand: NEC Pages: 146

Brand: ARE Pages: 39

Brand: Atari Pages: 16

Brand: INTERACT Pages: 15

320-00-00010-01

Brand: Life Fitness Pages: 36

Brand: Casio Pages: 81

Brand: Asus Pages: 18

Brand: Asus Pages: 174

Brand: Asus Pages: 166

Brand: Dell Pages: 57

Brand: Dell Pages: 80

Brand: Dell Pages: 112

Brand: Dell Pages: 78

Brand: Dell Pages: 57

Brand: Dell Pages: 144

OptiPlex 5480 All-in-One

Brand: Dell Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands