Advantech-DLoG DLT-V6210 Quick Start And Installation Manual Download Page 4

Page: 4 / 12

Closing the antenna cap:

−

Place the antenna cap back onto DLT-V6210. The antenna cap seal must not

be damaged; it must be seated correctly in the groove.

−

Tighten the two screws of the antenna cap again (1 Nm torque).

Overview of operation elements

NOTE

: Users of the DLT-V6210 must be trained by skilled personnel and

instructed about the operation of the device.

Operate the touchscreen with:

−

Clean, dry fingers

−

Clean, dry, thin gloves

−

Suitable touch stylus

Function of the front keys (left side):

−

Power on/off

−

LCD Brightness up

−

LCD Brightness down

LED indication:

System Status

LED Status

System power on

Static on

System power off

Off

System over/under

temperature

Blinking

0.2 sec. on / 0.8 sec. off

System thermal

sensor faulty

Blinking

0.5 sec. on / 0.5 sec. off

Summary of Contents for DLT-V6210













Search results

Summary of Contents for DLT-V6210

Reviews:

Related manuals for DLT-V6210

Brands by name

Popular brands

Advantech-DLoG DLT-V6210, Quick Start And Installation Manual

Search results

Summary of Contents for DLT-V6210

Reviews:

Related manuals for DLT-V6210

Brands by name

Popular brands