3.51 Options Enable Pass Codes
The Options Enable Screen is used at the factory to “enable” options for use by the operator. A status box
is located to the left of the option to indicate if the option is available to operator. If OFF, the option
settings screen will not be displayed for use by the operator. See Figures 3-76 and 3-78.
Options must be purchased from Advanced Poly-Packaging, Inc. to obtain the password. Contact
Advanced Poly-Packaging, Inc. Service Dept. for more information regarding options available for the
T-1000.
3.52 Valve Station Setup
The T-1000 is equipped with a valve station that is wired from DB25 connector/open ended cable to the
PLC. Each wire is pre-assigned to a PLC output, but options that are available are not assigned to a
solenoid valve until the machine is ready to ship from the factory.
Each valve is assigned a “station” number. Stations 1 through 4 are fixed and programmed to operate a
standard T-1000 in a fixed sequence of operation. However, when options are added, the sequence of
operation changes. Additionally, outputs from the PLC to the valve are assigned, depending on the options
equipped.
For instance, if a LS-10 Load Shelf option is added and the valve station assigned is #6, the T-1000 Valve
Setup Screen must be accessed and the Load Shelf option assigned to Station #6. See Figure 3-78.
To assign an option to a Valve Station, press the option and on the number keypad, press the number
followed by the <Enter> button.
Note: You will not be able to assign two options to the same Station number. A message screen will be
displayed if you attempt to assign two options to the same Valve Station number. The message will also be
displayed if you attempt to leave the Valve Station setup screen with two options assigned to the same
valve.
To start over, press the <Reset> button. Contact APPI Technical Support for assistance.
3.53 APPI Factory
DEFAULT SETTINGS-will default all the settings back to the factory settings
EEPROM- allows to write in the prompt sections, or READ to change a previous entry
SERVICE CENTER-
FRAME TYPE-Horizontal or vertical
Pressing the Machine Setting button will take you to the Machine Info Screen. See Figure 3-80
Information about the machine will be provided on this screen.
This screen is also accessed from the Main Menu.
Select the Machine Setting button to access:
Bag Settings for the current job running and Factory Settings that were originally set up on the machine by
APPI. See Figure 3-81
57
57
Summary of Contents for Advanced Poly-Bagger T-1000-S14
