background image

ANTENNAS INSTALLATION

Antennas should  be mounted on a 

Non-Enclosed

and 

Non-Metallic 

material 

such as clear glass or plastic trim panels. Recommended  placements for the 
Front-Antenna is on the top-left corner  of the front windshield  and bottom-left 
corner of the rear windshield  for the Rear-Antenna. The Bypass-Antenna  can be 
placed around the edge of the front windshield  so it can sense the Bypass 
Transponder Card within one inch away from outside of the vehicle. Do  not place 
antenna in locations that will be shield by metallic material. 

Test for coverage and range after installation to determine the optimal locations 
for the antennas. You may adjust antenna positions to other possible  placement 
locations as illustrated in the diagram. Use double  sided  tape to secure antennas 
after final positions are confirmed.

Ignition-Controlled Door Lock

Enabled by default and controlled by Brake input, this function will provide:

Auto Door 

Locking

when ACC  is turned  ON while brake is applied.

Auto Door 

Re-Locking

when brake applied  after door opened-then-closed.

Auto Door 

Unlocking

when  ACC is OFF.

To 

disable

Ignition-Controlled Door Lock feature, press  and hold the brake pedal 

when powering  ON the controller. Horn  output will sound  2x if this feature is 
disabled or 1x if this feature enabled.

PROGRAMMABLE FEATURES (CONT.)

Front Antenna 

Placement

Rear Antenna 

Placement

Main Antennas
5 - 6 Feet Range

Bypass Antenna
0.5 - 1 Inches Range

Other Possible 
Placement Locations

Bypass Antenna 

Placement

Antenna needs to be positioned away from any type of 

metallic material to achieve the best reception in all 

directions.  Avoid strain/pull on antenna wiring and do 

not bend or overlap Main antenna with Bypass antenna.

IMPORTANT

8

© Copyright Advanced Keys Inc. 2011.   All Rights Reserved. 

Summary of Contents for AK-104












Reviews: