4/2017
A - 23
56091206 - CS7010
ENGLISH - A
INSTRUCTIONS FOR USE
DETERGENT SYSTEM PREPARATION AND USE (ECOFLEX MODELS ONLY)
The Detergent Cartridges
(47)
are located below the Operator’s Seat
(2)
. Fill the detergent cartridge with a maximum of 2.2 gallons (8.32 Liters) of detergent.
SERVICE NOTE:
Remove the detergent cartridges from the machine prior to
fi
lling to avoid spilling detergent on the machine.
It is recommended that a separate cartridge be used for each detergent you plan to use. The detergent cartridges have a white decal on them so you can write the
detergent name on each cartridge to avoid mixing them up. When installing a new cartridge, remove the Cap
(BC)
and place the cartridge in the detergent box.
Install the Dry Break Cap
(BD)
as shown in
Figure 10
.
The system should be purged of previous detergent when switching to a different detergent.
SERVICE
NOTE:
Move machine over
fl
oor drain before purging
because a small amount of detergent will be dispensed in the process.
To Purge When Changing Detergents (SCRUB AND SOLUTION SYSTEMS MUST BE OFF)
1.
Disconnect and remove the detergent cartridge.
2.
Turn the key switch
(A)
to the RUN (ON) position. Wait a few seconds for the start-up sequence to
fi
nish.
3.
Press and hold the Solution Switch
(U)
and the Detergent Switch
(X)
for approximately 2 seconds. Release the switches when the Detergent Purge indicator
(C12)
appears on the display (the Detergent Switch Light
(X1)
and Solution Switch Light
(U1)
will be ON.
NOTE:
Once activated the purge process takes 20
seconds. Press
(U)
and
(X)
again before 20 seconds to cancel purge. See
Figure 10
for Detergent System indicators. Normally one purge cycle is adequate
to purge the system.
To Purge Weekly (SCRUB AND SOLUTION SYSTEMS MUST BE OFF)
1.
Disconnect and remove the detergent cartridge. Install and connect a Cartridge
fi
lled with clean warm water.
2.
Follow steps 2 and 3 from “To Purge When Changing Detergents”.
When the detergent level is nearing the bottom of the cartridge it is time to re
fi
ll or replace the cartridge(s).
SERVICE NOTE:
Follow the “To Purge Weekly” instructions above if the machine is going to be stored for an extended period of time.
Detergent Ratio (SCRUB SYSTEM MUST BE ON)
No detergent is dispensed until the scrub and detergent systems are activated and the Drive Pedal
(37)
is pushed forward.
The Detergent Indicator
(C6)
will be displayed in scrub mode when the detergent system is installed on the machine.
The Detergent Ratio Indicator
(C7)
will display the selected ratio when the detergent system is on.
Four Modes of EcoFlex Operation
1
.
Plain Water Cleaning Mode
- During scrubbing, the detergent system can be turned off at any time by pressing the Detergent Switch
(X)
to allow
scrubbing with water only. Detergent Ratio Indicator
(C7)
will be blank and Detergent Indicator Bar Graph
(C8)
will display no bars
fi
lled. Detergent
Light
(X1)
will be off.
2
.
Minimum Concentration Detergent Mode
– Activated by pressing the Detergent Switch
(X)
when detergent is off (repeated presses will cycle to
maximum Mode, off and back to minimum mode). Detergent Ratio Indicator
(C7)
will display the current minimum detergent level and Detergent
Indicator Bar Graph
(C8)
will display
fi
rst bar
fi
lled. Detergent Light
(X1)
will be on. See below the steps “To program the Minimum Detergent Level”.
3
.
Maximum Concentration Detergent Mode
– Activated by pressing the Detergent Switch
(X)
when detergent is at minimum mode (repeated presses
will cycle to minimum mode, off and back to maximum mode). Detergent Ratio Indicator
(C7)
will display the current maximum detergent level
and Detergent Indicator Bar Graph
(C8)
will display left and right bars
fi
lled. Detergent Light
(X1)
will be on. See below the steps “To program the
Maximum Detergent Level”. Do not use a concentration level exceeding the detergent manufacturer’s recommendation.
4
.
Burst of Power
Cleaning Mode
– Press the Burst of Power Switch
(S)
to increase the detergent ratio for one minute to the pre-programmed
“maximum concentration” detergent level (as noted in programming instructions below). Detergent system will be turned ON at “minimum
concentration” detergent level if it was off. This will also cause the solution
fl
ow rate to increase to the next level and the scrub pressure to increase
to the next level. Burst of Power Indicator
(C34)
will blink for one minute on the display along with a 60 second timer countdown. Press the Burst of
Power Switch
(S)
again before 60 seconds to cancel Burst of Power. The amount of time Burst of Power runs is adjustable (see “Information Menu
Display” submenu “Options”).
To program the Maximum Concentration Detergent Level
1.
Press the OneTouch™ Scrub switch
(R)
to activate the scrub system.
2.
Press and release Detergent Switch
(X)
until you have entered the maximum concentration detergent mode (
(C8)
shows left and right bars
fi
lled).
3.
Press and hold the Detergent Switch
(X)
for approximately 2 seconds until the Ratio Indicator
(C7)
fl
ashes.
4.
While the ratio is
fl
ashing, pressing and releasing the detergent switch will cycle through the available ratios (300:1, 256:1, 200:1, 150:1, 128:1, 100:1, 64:1,
50:1, 32:1).
5.
Once the desired ratio is displayed on the screen, stop and it will save the setting after 3 seconds.
6.
Whenever the maximum concentration detergent setting is set to a lower concentration than the current minimum programmed concentration setting, the
minimum concentration default setting will be equal to the maximum concentration setting until changed by the operator.
To program the Minimum Concentration Detergent Level
1.
Press the OneTouch™ Scrub switch
(R)
to activate the scrub system.
2.
Press and release Detergent Switch
(X)
until you have entered the minimum concentration detergent mode (
(C8)
shows left bar
fi
lled).
3.
Press and hold the Detergent Switch
(X)
for approximately 2 seconds until the Ratio Indicator
(C7)
fl
ashes.
4.
While the ratio is
fl
ashing, pressing and releasing the detergent switch will cycle through the available ratios (Note: only ratios that are a lower concentration
or equal to the maximum detergent setting will be available.
5.
Once the desired ratio is displayed on the screen, stop and it will save the setting after 3 seconds.
Once set, the detergent
fl
ow rate automatically increases and decreases with the solution
fl
ow rate, but the detergent ratio remains the same.
