manualshive.com logo in svg

ADTEK AEM-DRB, Operation Manual, Page: 25 / 44

Share
Download
ADTEK AEM-DRB Operation Manual Download Page 25

21

4.1.5.3 Current Transformer Setting

• CT Primary: The setting range of Ampere of CT primary side is 5~9999 A. The default 

value is 5 A.

• CT Secondary: The setting range of Ampere of CT primary side is 1 A or 5 A. The default 

value is 5 A.

• Steps of setup are as follows:

1.  Press ENTER key on the menu page to enter the CT primary.
2.  Press UP or DOWN key to select the loop to be set, press ENTER key to enter.
3.  Press UP or DOWN key to select the numeric.
4.  Press LEFT key move to the next digit.
5.  Repeat step 3 to 4 until finishing ampere setting, press ENTER key to save and return 

to the previous menu.

4.1.5.2 Voltage Transformer Setting

• PT Primary: The setting range for the volt of PT primary side is 0~9999k V. The default 

value is 600 V.

• PT Secondary: The setting range for the volt of PT primary side is 50~600 V. The default 

value is 600 V.

• Steps of setup are as follows:

1.  Press ENTER key on the menu page to enter the volt of PT primary setting.
2.  Press UP or DOWN key to select and set the voltage value of loop A or loop B or the 

voltage unit of the PT primary, and press the ENTER key to enter.

3.  Press UP or DOWN key to select the numeric.
4.  Press LEFT key to move to the next digit.
5.  Repeat step 3 to 4 until finishing volt setting, press ENTER key to save and return to 

the previous menu.

6.  Press ENTER key to enter the voltage unit setting.
7.  Press UP or DOWN key to select the unit V or kV.
8.  Press ENTER key to save and return to the menu.
9.  The volt setting of PT secondary is the same as PT primary.

※  Press LEFT key to cancel input and return to the previous menu.

Voltage phase/line

input

Sub loop set up

1P2W

1P3W

3P3W

3P4W

1P2W

○

X

X

X

1P3W

○

○

X

X

3P3W

○

X

○

X

3P4W

○

X

○

○

※  Each group of loops can independently set the phase-line system for measurement, 

but there will be restrictions based on the voltage phase-line system connected to the 
main loop, see the table below:

Summary of Contents for AEM-DRB













































Reviews:

No comments