manualshive.com logo in svg

ADTEK AEM-DRB, Operation Manual, Page: 14 / 44

Share
Download
ADTEK AEM-DRB Operation Manual Download Page 14

10

Chapter 3 Installation

3.1 Installation Method

3.1.1 Environment

3.1.2 Remind

This product must be placed in the box when it is not in use. If it is not used for the time 

being, in order to make the product conform to the warranty scope and future maintenance 
of the company, please pay attention to the following matters during storage:
• Must be placed in a dust-free, dry place.
• The ambient temperature in the storage location must be kept in the range of -10 ℃ to 

+70℃ (14 ℉ to 158 ℉ ).

• The relative humidity in the storage location must be kept in the range of 5% to 95% 

without condensation.

• Keep the storage away from the environment containing corrosive gas and liquids.
• It is best to properly store in a rack or countertop.
• Suitable installation environments for this product include: places where there is no high 

heat  device;  locations  where  there  is  no  water  droplets,  vapors,  dust,  and  oily  dust; 
places where there is no corrosion, flammable gas, liquids; and where there is no floating 
dust and metal particles Places; Strong, vibration-free, electromagnetic noise-free places.

• Installation  method  must  be  in  accordance  with  the  regulations,  or  it  could  cause 

malfunction.

• To make sure the cooling loop work well, when installing the electric meter, it is necessary 

to keep sufficient space between the upper and lower side of the meter and the adjacent 
items and baffles (wall) or it will cause poor heat dissipation.

Summary of Contents for AEM-DRB













































Reviews:

No comments