ADRF PSR78 User Manual Download Page 20 | Manualshive

Page: 20 / 37

background image

PSR78 Repeater

User Manual V0.1

Page | 6

4.2.3 Side Navigation Bar

The side navigation bar located on the left hand side of the Web-GUI allows the user to switch between the two
technolgies supported by the system.

4.2.4 SMR700 Band / SMR800 Band

The band column displays the bandwidth that has been selected. The downlink column displays the center
frequency of the selected band. The uplink column displays the center frequency of the selected band.

4.2.5 Power & Gain

This section displays the Input, Gain, and Output for both downlink and uplink.

4.2.6 Alarm

This section displays the four (4) alarms statuses with three possible status conditions (Normal, Soft Fail or Hard
Fail).

«
...
18
19
20
21
22
...
»

Summary of Contents for PSR78






































Reviews:

No comments

Related manuals for PSR78

Brand: Jaga Pages: 2

Brand: VEAB Pages: 24

Brand: VITAE Pages: 72

Brand: Lasko Pages: 4

Brand: Bionaire Pages: 8

Brand: VonHaus Pages: 10

Brand: Ariston Pages: 11

SingleHeater SH 312 Series

Brand: IRT Pages: 20

Brand: Almost Heaven Saunas Pages: 8

Brand: L.B. White Pages: 96

Brand: Circutor Pages: 9

Brand: KASTOR Pages: 14

AROACE CH-MG150

Brand: Yazaki Pages: 28

Brand: Toolland Pages: 14

Brand: for Living Pages: 9

Brand: Sabiana Pages: 41

Brand: Adler Europe Pages: 72

Brand: Adler Europe Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands