ADRF PSR78 User Manual Download Page 26 | Manualshive

Page: 26 / 37

background image

PSR78 Repeater

User Manual V0.1

Page | 12

4.4.1.1 Bandwidth Selection

This section allows the user to specify the desired bandwidths and frequencies ranges to be amplified. First
select the desired bandwidth from the dropdown menu in the Bandwidth column. Next, input the center

frequencies of the desired frequencies and click the Set button. Once the Set button is pressed, desired
frequencies will be highlighted in the frequency table.

4.4.1.2 Custom Bandwidth Setting

This section allows the user to download custom filter bandwidth. The PSR78 supports bandwidths
selections in 250 KHz steps. If there are any special applications that require custom bandwidth, please

contact our Sales department.

4.4.1.3 Location

This section allows the user to input the latitude and the longitude of the repeater.

4.4.1.4 Modem Box Settings:

This section allows the user to specify an alternative Repeater IP, Subnet Mask, and Gateway settings.

These settings are enabled when the Host/Remote switch is set to the Remote position. When the
Host/Remote switch is changed, the repeater will reboot and will result in a temporary loss in coverage.

«
...
24
25
26
27
28
...
»

Summary of Contents for PSR78






































Reviews:

No comments

Related manuals for PSR78

Brand: Rasonic Pages: 8

Brand: wallas Pages: 18

Brand: Pace Pages: 13

Brand: Flagro Pages: 14

SAVANA SAV-MIX Series

Brand: 2VV Pages: 114

Brand: Glowworm Pages: 56

Brand: Singer Pages: 36

Brand: THERMOFAN Pages: 8

Brand: Entel Pages: 12

TRV-220-220M-222

Brand: Fagor Pages: 26

Brand: heatness Pages: 54

Brand: Twin-Star International Pages: 12

Brand: Circutor Pages: 9

Brand: Frico Pages: 19

Brand: Warm Tech Pages: 67

Brand: Ouellet Pages: 2

Brand: United States Stove Company Pages: 188

Brand: Black Box Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands