background image

The information in this document is subject to change without notice and should not be construed as a commitment 
by ADP, Inc.   ADP is not responsible for any technical inaccuracies or typographical errors which may be contained 
in this publication. Changes are periodically made to the information herein, and such changes will be incorporated 
in new editions of this publication. ADP may make improvements and/or changes in the product and/or the programs 
described in this publication at any time without notice. 

This document or any part thereof may not be reproduced in any form without the written permission of Kronos 
Incorporated. All rights reserved. © 1999, 2000, Kronos Incorporated.

ADP provides this publication "as is" without warranty of any kind, either express or implied, including, but not limited 
to, the implied warranties of merchantability or fitness for a particular purpose.

ADP is a registered trademark of ADP of North America, Inc. eTIME is a registered trademark of Automatic Data 
Processing, Inc.  

When using and applying the information generated by ADP products, customers should ensure that they comply 
with the applicable requirements of federal and state law, such as the Fair Labor Standards Act.

FCC Compliance

After testing, this equipment complies with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. 
These limits provide reasonable protection against harmful interference when this equipment is operated in a 
commercial environment. This equipment generates, uses, and can radiate radio frequency energy. If it is not 
installed and used in accordance with the instruction manual, it can cause harmful interference to radio 
communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which 
case, the user, and not Kronos Incorporated, is required to correct the interference.

Canadian DOC Compliance

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in 
the Radio Interference Regulations of the Canadian Department of Communications.

Cet appareil numérique respecte les limites de rayonnement de bruits radioélectriques applicables aux appareils 
numériques de classe A, prévues au Règlement sur le matériel brouilleur du ministère des Communications du 
Canada.

EN 55022 (CISPR 22)

This product is a Class A product. In a domestic environment, it may cause radio interference in which case the user 
may be required to take adequate measures.

Published by ADP, Inc.

ADP, Inc.

One ADP Boulevard
Roseland, NJ 07068

For more information, see the ADP, Inc. Web page:

http://www.ADP.com

Document Revision History  

Document Revision

 Release Date

A

June  2000

B

July  2000

Summary of Contents for 14.4Kbps















Reviews: