ADLINK Technology NuPRO-720 User Manual Download Page 90

Page: 90 / 98

POST Messages

Reserved

KBC final Init

Final Initial KBC and setup BIOS data area

Reserved

Initialize Video Inter-
face

Read CMOS location 14h to find out type of video in
use. Detect and Initialize Video Adapter.

Reserved

Video memory test

Test video memory, write sign-on message to
screen. Setup shadow RAM - Enable shadow
according to Setup.

Reserved

PS2 Mouse setup

Setup PS2 Mouse and reset KB

Reserved

Test DMA Controller 0 Test DMA channel 0

Reserved

Test DMA Controller 1 Test DMA channel 1

Reserved

Test DMA Page Reg-
isters

Test DMA Page Registers.

Reserved

Test Timer Counter 2

Test 8254 Timer 0 Counter 2.

Reserved

Test 8259-1 Mask Bits Verify 8259 Channel 1 masked interrupts by alter-

nately turning off and on the interrupt lines.

Reserved

Code

(hex)

Name

Description

Summary of Contents for NuPRO-720



































































































Search results

Summary of Contents for NuPRO-720

Reviews:

Brands by name

Popular brands

ADLINK Technology NuPRO-720, User Manual

Search results

Summary of Contents for NuPRO-720

Reviews:

Brands by name

Popular brands