manualshive.com logo in svg

ADLINK Technology LitleBoard 800, Reference Manual

Share
Download
ADLINK Technology LitleBoard 800 Reference Manual Download Page 33

Chapter 3

Hardware 

LittleBoard 800

Reference Manual

27

Speaker

The signal lines for a speaker port with 0.1-watt drive are provided through a Utility 1 interface (J15).  

Note:

The shaded area denotes power or ground. The signals marked with * = Negative true logic.

Utility 2 Interface

The Utility 2 (J13) interface consists of a 24-pin connector used to interface various signals to the external 
board with external connections, or directly to the respective connector such as, the mouse, USB, etc. 

Table 3-9 on page 29

 lists the pin signals for the Utility 2 interface. The J13 connector uses 24 pins, 2 rows, 

odd/even (1, 2) with 0.100" pitch.

•

PS/2 Mouse signals

•

Infrared (IrDA) signals 

•

SMBus signals

•

USB signals for USB ports 1 and 2

•

Power button signal

Table 3-7.   Utility 1 Interface Pin/Signal Descriptions (J15)

Pin #

Signal

I/O

Description

1

-12V

I

-12 Volts – Supplied from external power source.

2

GND

I

Ground

3

-5V

I

-5 Volts – Supplied from external power source.

4

GND

I

Ground

5

LED

O

Power On LED – This on-board +3.3 volts is provided through 330 ohm 
resistor to an external Power-On LED.

6

NC

-

Not connected (Power Good)

7

SPKR+

O

+ Speaker Output – This signal drives external PC "Beep" speaker.

8

GND

I

Ground

9

RSTSW*

I

Reset Switch – This signal (ground) provided from external reset switch. 

10

NC

-

Not connected (Keyboard Switch)

11

KBDATA

I/O

Keyboard Data signal provided to external keyboard connector.

12

KBCLK

I/O

Keyboard Clock – Clock signal provided to external keyboard connector.

13

GND

I

Keyboard Ground

14

KBDPWR

O

Keyboard Power  – This +5 volts is provided to external keyboard 
connector. Requires external fuse for keyboard/mouse protection.

15

BATV+

I

Backup Battery – This connection provides an additional backup battery 
from an external source. It can also be used in place of the on-board 
backup battery, B1, shipped with all LittleBoard 800s. Each RTS battery 
input is protected with a zener diode.

16

BATV-

I

Battery - Return (Grounded) 

Summary of Contents for LitleBoard 800



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands