manualshive.com logo in svg

ADLINK Technology LitleBoard 800, Reference Manual

Share
Download
ADLINK Technology LitleBoard 800 Reference Manual Download Page 12

Chapter 2

Product Overview

6

Reference Manual

LittleBoard 800

•

Keyboard/Mouse Interface 

♦

Provides PS/2 keyboard interface 

♦

Provides PS/2 mouse interface 

•

Audio interface 

♦

Provides AC’97 CODEC on board

♦

Supports AC’97 standard

•

Ethernet Interface 

♦

Provides two fully independent Ethernet ports

♦

Provides integrated LEDs on each port (Link/Activity and Speed)

♦

Provides Intel 82551ER and 82541(GI/PI) controller chips

♦

Provides extra header for LAN LED signals (gigabit only)

♦

Supports IEEE 802.3 10/100BaseT and 10/100/1000BaseT compatible physical layers

♦

Supports Auto-negotiation for speed, duplex mode, and flow control

♦

Supports full duplex or half-duplex mode

•

Full-duplex mode supports transmit and receive frames simultaneously

•

Supports IEEE 802.3x Flow control in full duplex mode

•

Half-duplex mode supports enhanced proprietary collision reduction mode

•

Video Interfaces (CRT/LVDS) 

♦

Support CRT (2048 x 1536) with up to 64MB UMA (Unified Memory Architecture)

♦

AGP 4X equivalent graphics performance

♦

Dual channel 9-, 12-, or 18-bit LVDS

♦

LVDS outputs (1 or 2 channel, four differential signals: 3-bits + clock) 

•

Miscellaneous

♦

Real-time clock (RTC) with replaceable battery 

♦

Battery-free boot (Boots even if battery is dead or missing) 

♦

Supports both on-board or external battery for Real Time Clock operation 

♦

Thermal and Voltage monitoring 

♦

Oops! Jumper (BIOS recovery) support 

♦

Serial Console 

♦

Watchdog timer (WDT) 

Summary of Contents for LitleBoard 800



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands