manualshive.com logo in svg

ADLINK Technology LitleBoard 800, Reference Manual

Share
Download
ADLINK Technology LitleBoard 800 Reference Manual Download Page 11

Chapter 2

Product Overview

LittleBoard 800

Reference Manual

5

♦

400MHz FSB 

•

Memory 

♦

Single standard 184-pin DDR DIMM slot

♦

Supports non-ECC or unbuffered ECC memory

♦

Su2.5V DDR RAM up to 1GB 

♦

Supports up to PC2700 DDR 333 (166MHz)

•

PC/104-Plus Bus Interfaces 

♦

PCI Bus up to 33MHz

♦

PCI 2.2 compliant signals 

♦

PC/104 (ISA) Bus up to 8MHz 

•

IDE Interfaces

♦

Provides two enhanced IDE controllers (4 devices)

♦

Supports dual bus master mode 

♦

Supports Ultra DMA 33/66/100 modes

♦

Supports ATAPI and DVD peripherals

♦

Supports IDE native and ATA compatibility modes

•

Floppy Disk Interface 

♦

Supports one standard floppy disk drive interface

♦

Supports all standard PC/AT formats: 360KB, 1.2MB, 720KB, 1.44MB, 2.88MB

•

Parallel Port

♦

Provides a standard printer interface

♦

Supports IEEE standard 1284 protocols of EPP and ECP outputs

♦

Supports Bi-directional data lines

♦

Supports 16 byte FIFO for ECP mode.

•

Serial Ports 

♦

Four buffered serial ports with full handshaking

♦

Provides 16550-equivalent controllers, each with a built-in 16-byte FIFO buffer

♦

Supports full modem capability on two of the four ports

♦

Supports RS232, RS485, or RS422 operation on each port

♦

Supports programmable word length, stop bits, and parity

♦

Supports 16-bit programmable baud-rate generator and an interrupt generator

•

USB Ports 

♦

Provides two root USB hubs

♦

Provides up to four USB ports 

♦

Supports USB boot devices 

♦

Supports USB v2.0 EHCI and UHCI v1.1

♦

Supports over-current detection status 

•

Infrared Interface 

♦

Supports IrDA 1.1 signals through Utility 2 connector

Summary of Contents for LitleBoard 800



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands