ADLINK Technology DMI-1210 User Manual Download

Page: 93 / 103

DMI-1210

SATA Test Mode

Disable

Enable

Test Mode Enable / Disable.

Aggressive LPM

Support

Disable

Enable

Enable PCH to Aggressively enter

link power state.

SATA0

Info only

Software Preserve

Info only

Port 0

Disabled

Enabled

Enable / Disable SATA Port

SATA Port 0 Hot

Plug Capability

Disabled

Enabled

If enabled, SATA port will be reported

as Hot Plug capable.

Configured as

eSATA

Info only

Display Configured as eSATA

support.

Mechanical

Presence Switch

Disabled

Enabled

Controls reporting if this port has a

Mechanical Presence Switch.
Note. Request Hardware support.

Spin Up Device

Disabled

Enabled

If enabled for any of ports Staggered

Spin Up will be performed and only

the drives which have this option

enabled will spin up at boot.
Otherwise all drives spin up at boot.

SATA Device Type

Hard Disk Drive

Solid State Drive

Identify if the SATA port is connected

to Solid State Drive or Hard Disk

Drive.

SATA Port 0 DevSlp

Disabled

Enabled

Enable/Disable SATA Port 0 DevSlp.

Board rework for LP needed before

enable.

DITO Configuration

Disabled

Enabled

Enable/Disable DITO Configuration

DITO Value

625

DITO Value.
Note. DITO Value can be accessed if

DITO Configuration item is enabled.

DM Value

DM Value.
Note. DM Value can be accessed if

DITO Configuration item is enabled.

SATA1

Info only

Software Preserve

Info only

Port 1

Disabled

Enabled

Enable / Disable SATA Port

BIOS Item

Options

Description

Summary of Contents for DMI-1210








































































































Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands

ADLINK Technology DMI-1210, User Manual

Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands