ADLINK Technology DMI-1210 User Manual Download

Page: 87 / 103

DMI-1210

6.5

Chipset Menu

6.5.1

North Bridge

Displays memory information, sets maximum value for TOLUID

and enables/disables BIOS assignment and PCIe VGA work-
around.

6.5.2

South Bridge

Sets IRQ mode and enables/disables SMBUs and PCI clock run.

BIOS Item

Options

Description

North Bridge

Submenu

South Bridge

Submenu

Uncore

Configuration

Submenu

South Cluster

Configuration

Submenu

BIOS Item

Options

Description

Memory Information Info only
Total Memory

Info only

Display Total Memory Size.

Memory Voltage

Info only

Display Memory Voltage.

Memory Slot0

Info only

Display Installed Memory Slot0

Information.

Max TOLUD

2 GB

2.25 GB
2.5 GB
2.75 GB
3 GB

Maximum Value of TOLUD.

PCIE VGA

Workaround

Disable

Enable

Enable if your PCIe card cannot boot

to DOS. This is for testing only.

BIOS Item

Options

Description

Serial IRQ Mode

Quiet

Continuous

Configure Serial IRQ Mode.

SMBus Support

Disable

Enable

Enable / Disable SMBus Support.

PCI CLOCK RUN

Disable

Enable

Display Installed Memory Slot0

Information.

Summary of Contents for DMI-1210








































































































Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands

ADLINK Technology DMI-1210, User Manual

Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands