manualshive.com logo in svg

ADLINK Technology aTCA-9710, User Manual

Share
Download
ADLINK Technology aTCA-9710 User Manual Download Page 33

 
 

 

33

aTCA-9710 

4.1.5 

System Firmware Progress Sensor 

Sensor 
Type 

Sensor 
Type Code 

Sensor 
Specific Offset 

Event 

System 
Firmware  
Progress 
(formerly 
POST  
Error) 

0Fh 00h 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
01h 
 
 
 
 
02h 

System Firmware Error (POST Error)  
The Event Data 2 field can be used to provide an event 
extension code, with the following definition:  
Event Data 2  
00h    Unspecified.  
01h    No system memory is physically installed in the 
system.  
02h    No usable system memory, all installed memory 
has experienced an unrecoverable failure.  
03h    Unrecoverable hard-disk/ATAPI/IDE device failure.  
04h    Unrecoverable system-board failure.  
05h    Unrecoverable diskette subsystem failure.  
06h    Unrecoverable hard-disk controller failure.  
07h    Unrecoverable PS/2 or USB keyboard failure.  
08h    Removable boot media not found  
09h    Unrecoverable video controller failure  
0Ah   No video device detected  
0Bh   Firmware (BIOS) ROM corruption detected   
0Ch   CPU voltage mismatch (processors that share 
same supply have mismatched voltage requirements)  
0Dh   CPU speed matching failure  
0Eh to FFh  reserved  
 
System Firmware Hang (uses same Event Data 2 
definition as  
following System Firmware Progress offset) 
 
System Firmware Progress  
The Event Data 2 field can be used to provide an event 
extension  
code, with the following definition:  
Event Data 2  
00h      Unspecified.  
01h      Memory initialization.  
02h      Hard-disk initialization  
03h      Secondary processor(s) initialization  
04h      User authentication  
05h      User-initiated system setup  
06h      USB resource configuration  
07h      PCI resource configuration  
08h      Option ROM initialization  
09h      Video initialization  
0Ah     Cache initialization  
0Bh     SM Bus initialization  
0Ch     Keyboard controller initialization  
0Dh     Embedded controller/management controller 
initialization  
0Eh     Docking station attachment  
0Fh     Enabling docking station  
10h      Docking station ejection  
11h      Disabling docking station  
12h      Calling operating system wake-up vector  

Summary of Contents for aTCA-9710























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands