ADJ ENC846 User Manual Download Page 6

6

SAFETY PRECAUTIONS

•  To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

•  Do not spill water or other liquids into or onto the unit.

•  Do not attempt to operate this unit if the power cord has been frayed or broken. 

•  Do not attempt to remove or break off the ground prong from the electrical cord. This prong is 

used to reduce the risk of electrical shock or fire in the event of an internal short.

•  Disconnect from main power before making any type of connection.

•  Do not remove the cover for any reason. There are no user serviceable parts inside.

•  Never operate this unit with the cover removed.

•  Never plug this unit into a dimmer pack.

•  Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6 in 

(15cm) between this device and a wall.

•  Do not attempt to operate this unit if it has been damaged in any way.

•  This unit is intended for indoor use only. Use of this product outdoors voids all warranties.

•  During long periods of non-use, disconnect the unit’s main power.

•  Always mount this unit in safe and stable matter.

•  Power-supply cords should be routed so that they are not likely to be walked on or pinched by  

items placed upon or against them, paying particular attention to the point at which the cords exit 

from the unit.

•  Cleaning - The fixture should be cleaned only as recommended by the manufacturer. See the 

Cleaning section of this manual for details.

•  Heat - The appliance should be situated away from heat sources such as radiators, heat registers,  

stoves, or other appliances (including amplifiers) that produce heat.

•  The fixture should be serviced by qualified service personnel when:

A.  The power-supply cord or the plug has been damaged.

B.  Objects have fallen onto, or liquid has been spilled into, the fixture.

C.  The fixture has been exposed to rain or water.

D.  The fixture does not appear to operate normally or exhibits a marked change in performance.

E.  The fixture has fallen and/or has been subjected to extreme handling.

Summary of Contents for ENC846

























Reviews: