ADIATEK Opal 66 Use And Maintenance Download Page 4

 

 

 

 

GENERAL RULES OF SAFETY 

 

The rules below have to be followed carefully in order to avoid injury to 

the operator and damage to the machine.  

 

Read the labels carefully on the machine. Do not cover them for any 

reason and replace them immediately if damaged.  

 

ATTENTION

: The machine must be used exclusively by authorized 

staff that have been instructed on its correct and proper use.  

 

ATTENTION

: Do not use the machine on areas having a higher 

gradient than the one stated on the number plate. 

 

ATTENTION

: The machine is not to be used by persons, children 

included, with reduced physical, sensorial or mental capabilities, or 

with lack of experience or knowledge, unless they could benefit, 

through the intermediation of a responsible person for their safety, 

by a supervision or instructions concerning to its use. 

 

During the operation of the machine, pay attention to other people 

and especially to the children. 

 

Children shall not play with the machine. 

 

Children cannot carry out cleaning and maintenance of the machine. 

 

 

TRANSFER 

 

 

Do not strike shelvings or scaffoldings where there is danger of 

falling objects.  

 

Leaving the machine in parking position, take off the key and act 

upon the parking brake. 

 

Do not use the machine as a means of transport.  

 

Adapt the working speed to the adhesion conditions: particularly, 

slow down before narrow curves have to be faced.  

 

 

STORAGE AND DISPOSAL  

 

 

Storage temperature: between 0°C and +55°C (32°F e 131°F). 

 

Perfect operating temperature: between 0°C and +40°C (32°F e 

104°F). 

 

The humidity should not exceed 95%.  

 

Provide for the scrapping of the material of normal wear (brushes, 

squeegee blades etc.) following strictly the respective rules.  

When your machine has to stop activity, provide for the appropriate 

waste disposal of its materials, especially oils, batteries and electronic 

components, and considering that the machine itself has been, where 

possible, constructed using recyclable materials. 

 

 

CORRECT USE 

 

 

Do not use the machine on surfaces covered with inflammable 

liquids or dusts (for example hydrocarbons, ashes or soot). 

 

In case of fire, use a powder based fire-extinguisher. Do not use 

water. 

 

Do not use the machine in explosive atmosphere.  

 

The machine has to carry out simultaneously the operations of 

washing and drying. Different operations must be carried out in 

restricted areas prohibited to non-authorized personnel and the 

operator has to wear suitable shoes. 

 

Signal the areas of moist floors with suitable signs.  

 

Do not mix different detergents, avoiding harmful odours.  

 

Avoid brushes operation when the machine is standing still in order 

to prevent floor damages. 

 

Before lifting the recovery tank, make sure that it is empty. 

 

 

MAINTENANCE 

 

 

If the machine does not work properly, check by conducting simple 

maintenance procedures. Otherwise, as for technical advice from an 

authorized assistance centre.  

 

For any cleaning and/or maintenance operation take off the power 

supply from the machine.  

 

Where parts are required, ask for ORIGINAL spare parts from the 

distributor and/or from an authorized dealer. 

 

 

 

Use only ORIGINAL brushes indicated in the paragraph 

“RECOMMENDED BRUSHES". 

 

Do not take off the protections which require the use of tools for 

their removal.  

 

Do not wash the machine with direct water, jets or with high water 

pressure nor with corrosive material.  

 

Every 200 working hours have a machine check by an authorized 

service department. 

 

Before using the machine, check that all panels and coverings are in 

their position as indicated in this use and maintenance catalogue. 

 

Restore all electrical connections after any maintenance operation. 

 

 

Summary of Contents for Opal 66




















Reviews: