Adey CP1-03-04913, Installation And Servicing

Page: 15 / 19

- 28 - - 29 -
10 TECHNICAL SPECIFICATION
ADEY reserve the right to amend the specification without notice .
10 .11 Noise: The equivalent continuous A-weighted sound pressure level at a
distance of 1 metre from the pump does not exceed 70 dB(A) .
11 TROUBLE SHOOTING GUIDE
Symptoms Error Code Probable Cause Recommended Action
No power Blank screen
No power to APU
Internal re-settable
fuse tripped
Check power supply/fuse
Disconnect APU from mains power for 20 seconds & and then re-connect
Pump(s) not
starting
No power to APU Ensure the green light is on the front of the APU, check fuse .
Low water Low water in tank
Depress float valve to varify water is filling tank, check water level and
supply .
System pressure =
set pressure
APU functioning correctly . Check the set system pressure .
Pump run fail Pump seized
Force the pumps to run using the pump test function . Clear error .
Pump run fail System pressure set
too high
System set pressure is set higher than the pump performance capability,
reduce set pressure . Ensure you have purchased the correct APU for the
system pressure required .
Sensor error Pressure sensor fault Remove pressure from the APU outlet and verify the displayed pressure
is 0 bar . Error will be displayed if the sensor signal is outside parameters .
(Replace sensor – call ADEY Customer Services) .
Pump(s) will not
stop
Sensor error
System pressure set
too high
System set pressure is set higher than the pump performance capability,
reduce set pressure . Ensure you have purchased the correct APU for the
system pressure required .
Pressure sensor fault Remove pressure from the APU outlet and verify the displayed pressure
is 0 bar . Error will be displayed if the sensor signal is outside parameters .
(Replace sensor – call ADEY Customer Services) .
Low pressure alarm
triggered
Low pressure
Leak in system . Check system for leaks . Check pump activity in logs . Check for leaking
pressure relief valve .
Low pressure alarm
set too high .
Reduce Low press alarm pressure . Check system pressure range during
normal operation .
Sensor error Pressure sensor fault Remove pressure from the APU outlet and verify the displayed pressure
is 0 bar . Error will be displayed if the sensor signal is outside parameters .
(Replace sensor – call ADEY Customer Services) .
High pressure
alarm triggered
High pressure System pressure
too high
Check system operation . Increase High presure alarm set pressure .
Sensor error Pressure sensor fault Remove pressure from the APU outlet and verify the displayed pressure
is 0 bar . Error will be displayed if the sensor signal is outside parameters .
(Replace sensor – call ADEY Customer Services) .
Pump run time
alarm activated .
Pump running for
longer than set
time
Pump run time
alarm
Pump filling system Activate system fill option to suppress alarm for 24 hours .
Leak in system Check system for leakage . Monitor using system fill volume log, reset if
needed .
Increase pump run time limit .
Activity high alarm
activated . Pump
starting more than
set value
Activity High
alarm
Pump filling system Activate system fill option to suppress alarm for 24 hours .
Leak in system Check system for leakage . Monitor using system fill volume log, reset if
needed .
Activity High alarm
number too low
Increase the Activity High alarm value .
Sensor failure error Sensor error Pressure sensor
outside specifcation
Remove pressure from the APU outlet and varify the displayed pressure
is 0 bar . Error will be displayed if the sensor signal is outside parameters .
(Replace sensor – call ADEY Customer Services) .
Low water error
Low water
Loss of water supply
to APU
Depress float valve to verify water is filling tank and check water level and
supply .
Water level set
too low
Adjust water level by turning float, ensure upper level probe is in contact
with water when the fill valve is turned off .
Check water level prior to leaving unattended .
Water overflowing
warning pipe or
weir
Water level too high Check function of the fill valve, replace or adjust if needed .
Pump NRV leaking Isolate APU from system and mains water and replace non-return valve
and holder .
Midi 135
CP1-03-04913
Midi 150
CP1-03-04914
Midi 235
CP1-03-04915
Midi 250
CP1-03-04916
General Guarantee
2 year
Approvals CE
Features
System capacity Up to 300,000 litres
Mounting Wall or floor mount
Pump control system
✓ ✓ ✓ ✓
Intelligent control interface
✓ ✓ ✓ ✓
System fill mode
✓ ✓ ✓ ✓
Dry run protection
✓ ✓ ✓ ✓
Typical Noise 60 dB(A) 60 dB(A) 62 dB(A) 62 dB(A)
Materials
Break tank Polyethylene
Front cover Acrylic capped ABS
Performance
Maximum Fill Pressure 3 .5 bar (350 kPa) 4 .1 bar (410 kPa)
Maximum flow 17 l/min 20 l/min
Maximum inlet pressure (tank fill valve) 7 bar (700 kPa)
Maximum working pressure 6 bar
Ambient air temperature Min 4
o
C / Max 40
o
C
Relative humidity 95 % non-condensing
Min ./Max . water temperature Min 4
o
C / Max 23
o
C
Water tank Usable water capacity 8 litres
Inlet valve and fill rate Torbeck (side entry) 12 l/min
Fluid category CAT 5 (type AB air gap with weir)
Connections Cold water inlet and outlet 15 mm compression x 600 mm flexible hose
Overflow (compression fitting) G ¾ (19 - 23 mm diameter pipe)
Pump Number of pumps 1 2 1 2
Pump mode Duty Duty-standby Duty Duty-standby
Pump type / head / impeller Peripheral / brass / brass
Motor type Induction (thermal trip, auto reset)
Duty rating Continuous (S1)
Electrical Power supply (Vac/Ph/Hz) 230/1/50
Power consumption - P1 380 Watts 545 Watts
Current (full load) 1 .7 Amps 2 .4 Amps
Fuse rating 5 Amps
Power cable length 1 .5 metres (pre-wired)
Alarm output Multiple
Physical Enclosure protection IPX4
Width 415 mm
Depth 270 mm
Height 504 mm
Weight (including fittings) 13 .4 Kg 19 .4 Kg 13 .4 Kg 19 .4 Kg
Weight (Filled) 23 .4 Kg 29 .4 Kg 23 .4 Kg 29 .4 Kg