background image

¬.l

K0764  5/02 

LIMITED WARRANTY

 

Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, 
subsidiaries and affiliates ("Seller"), 165 Eileen Way, Syosset, New York 11791, warrants its products 
to be in conformance with its own plans and specifications and to be free from defects in materials and 
workmanship under normal use and service for 24 months from the date stamp control on the product 
or, for products not having an ADEMCO date stamp, for 12 months from date of original purchase 
unless the installation and setup guide or catalog sets forth a shorter period, in which case the shorter 
period shall apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of 
charge for materials or labor, any product which is proved not in compliance with Seller's 
specifications or proves defective in materials or workmanship under normal use and service. Seller 
shall have no obligation under this Limited Warranty or otherwise if the product is altered or 
improperly repaired or serviced by anyone other than ADEMCO factory service. For warranty service, 
return product transportation prepaid, to an authorized ADEMCO Distributor.

  THERE ARE NO 

WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR 
PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. 
IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL 
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON 
ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY 
THE SELLER'S OWN NEGLIGENCE OR FAULT. 

Seller does not represent that the products it sells may not be compromised or circumvented; that the 
products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or 
that the products will in all cases provide adequate warning or protection. Customer understands that 
a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or 
other events occurring without providing an alarm, but it is not insurance or a guarantee that such 
will not occur or that there will be no personal injury or property loss as a result.

 CONSEQUENTLY, 

SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER 
LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS 
HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING 
UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, 
SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE 
PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. 

This 

warranty replaces any previous warranties and is the only warranty made by Seller on this product. 
No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized

.

 

 

 

 

 

180 Michael Drive 

Syosset, New York 11791 

Copyright © 2002 PITTWAY CORPORATION 

Summary of Contents for TeleCommand





















Reviews: