manualshive.com logo in svg

ADE Accenta G3, Engineering Information, Page: 13 / 36

Share
Download
ADE Accenta G3 Engineering Information Download Page 13

Access Codes

There are four codes used in the system, all are 4
digit and can be set to any number from 0000 to
9999. The access codes ensure that only
authorised users can operate the system.

User 1 and 2 codes

The user 1 and user 2 codes have the same
operation for testing, Setting and Unsetting, but
user 1 code which is usually considered to be the
Managers code has the authority to add, change
or delete the user 2 code and duress code.

Duress code

Should be used in a hold up situation where
there is pressure to Set or Unset the system.
Entry of the code will allow the system to work
normally but also generate a silent PA type
alarm by operating the PA communicator output.

Engineer code

Accesses the Engineer Program mode to allow
the system to be programmed. The engineer
code will not set or unset the system.

If configured the Engineers access code can be
used to reset the system after an alarm.

Note:

Entering an invalid user code will

operate the code tamper. After nineteen
incorrect key pushes a full alarm
condition will be generated.

4PI175 issue 1_6/01

13

Accenta/Optima G3 intruder system

Engineering information

Access

Codes

Reset

Reset

Codes

Change User code 1

Change User code 2

Change Duress code

Change Engineer code

2

3

9

1

8

ZONE 1-4

n

n

n

n

New code

ZONE 1-4

Rising beeps

Attack

Exit codes

Leave engineer mode

Day

Tamper

Attack

Acknowledge

Day

Day

NOTE

- The sounder will produce

a flat beep if the code is rejected. The Code
is rejected if it is already in use.

Enter Engineer program mode

Example: To change User 1 code to 3457
Press:

9

Prog

9

9

9

4

Reset

Reset

8

1

3

5

7

Summary of Contents for Accenta G3





































Reviews:

No comments