manualshive.com logo in svg

ADE Accenta G3, Engineering Information, Page: 12 / 36

Share
Download
ADE Accenta G3 Engineering Information Download Page 12

Testing the system

Complete the wiring of the system and then:

ÿ

fully test the system and ensure it is fault
free.

ÿ

Fully program the system

ÿ

Fill in the installation log at the back of the
manual and retain if for future reference.

ÿ

Finally explain the operation of the system
to the end user. The Operating Instructions
are attached to the centre of this manual.
Detach them and leave them with the user.

Engineer program mode

The panel may be programmed to suit a wide
variety of installations. .
Once the

engineer program mode

has been

accessed, each configuration may be changed in
any order. As each configuration is completed
the system will automatically return to top level
of engineering program mode.

Before entering

engineer program mode

the

system should be in the Day mode, with the Day
and Power indicators lit.

Key

To exit

System indications

- Unset system indication

- Set system indication

To enter Engineer program mode

Note:

The factory configured engineer’s

access code is 9999. If however this code
is changed then enter the appropriate
code.

To Exit Engineer program mode

To reset panel to Factory set

conditions

CAUTION:

All configurations of the

panel are restored to factory ‘default’
conditions.

12

4PI175 issue 1_6/01

Engineering information

Accenta/Optima G3 Intruder system

Testing

the

system

Reset

Day

Prog

9

9

9

9

Tamper

Day

ZONE 1 - 8
Momentarily On

Acknowledge

Power

Day

Power

Reset

Quit the current function
Leave program menu
Down one menu level

LED steady On indication

LED Off

Strobe

Bell

NOTE: In general a flat beep is
an indication of an incorrect key press.

Sound description

Internal sound

External devices

ARC

o/p

Output to Alarm Receiving Centre

Communicator outputs are not applicable for
Optima compact G3 panel

LED flashing indication

reset beeps

Within 5 seconds of
powering up the panel

Reset

Reset

Summary of Contents for Accenta G3





































Reviews:

No comments