ADC AD-320 Installation Manual Download Page 54

Page: 54 / 60

American Dryer Corp.

112144 - 46

S. No heat (ELECTRIC MODELS ONLY)...both the Dual Microprocessor Controller (DMC)

computer heat indicator dot and “HEAT” output light emitting diode (L.E.D.) indicator are on...but
electric oven is not operating...

1. Fault in sail switch circuit...

a. Sail switch is out of adjustment or has failed.

b. Sail switch damper is not closing or is fluttering...

1) Lint drawer/screen is dirty or clogged.

2) Restriction in exhaust ductwork.

2. Fault in oven hi-limit circuit or thermostat.

3. Fault in basket (tumbler) hi-limit circuit or thermostat.

4. Failed oven contactor.

5. Failed oven electric element.

T. No heat (STEAM MODELS ONLY)...both the DMC computer heat indicator dot and “HEAT”

output L.E.D. indicator are on...but steam damper system is not operating...

1. Fault in basket (tumbler) hi-limit circuit or thermostat.

2. No external compressed air to steam damper (80 PSI [5.51 bar] required).

3. Steam damper is stuck or damper system airflow control valve is not adjusted properly.

4. Failed steam damper 24 VAC pneumatic solenoid switch.

5. Failed steam damper piston.

U. Dryer operates, but is taking too long to dry...

1. Exhaust ductwork run is too long or is undersized...back pressure

must be

no less than 0 and

cannot

exceed 0.3

inches (0.74 mb) water column (W.C.).

2. Low and/or inconsistent gas pressure (gas models only).

3. Insufficient make-up air.

4. Poor air/gas mixture at burner (gas models only)...yellow or poor flame pattern. Adjust gas burner air adjustment

shutters.

5. Lint drawer/screen is not being cleaned out on a regular basis or often enough.

6. Extractors (washers) are not performing properly.

7. Sail switch is fluttering...restriction in exhaust (gas and electric models only).

8. Failed DMC computer temperature sensor...temperature calibration is inaccurate.

9. Failed DMC computer...temperature calibration is inaccurate.

10. Failed burner/oven hi-limit (gas and electric model only).

11. Failed basket (tumbler) hi-limit thermostat.

Summary of Contents for AD-320





























































Search results

Summary of Contents for AD-320

Reviews:

Related manuals for AD-320

Brands by name

Popular brands

ADC AD-320, Installation Manual

Search results

Summary of Contents for AD-320

Reviews:

Related manuals for AD-320

Brands by name

Popular brands