ADC AD-320 Installation Manual Download Page 32 | Manualshive

Page: 32 / 60

background image

28

American Dryer Corp.

112144 - 46

The size of the main gas supply line (header) will vary depending on the distance this line travels from the gas
meter (or in the case of liquid propane [L.P.] gas, the supply tank), the number of tees, other gas-operated
appliances on the supply line, etc. Specific information regarding supply line size

should be

determined by the

gas supplier.

NOTE:

Undersized gas supply piping can create a low or inconsistent pressure, which will result in
erratic operation of the burner ignition system.

Consistent gas pressure is essential at

ALL

gas connections. It is recommended that a 3/4” (19.05 mm) pipe

loop be installed in the supply line servicing the bank of dryers. An in-line pressure regulator

must be

installed

in the gas supply line (header) if (natural) gas line pressure exceeds 12.0 inches (29.9 mb) water column (W.C.)
pressure. Refer to the

illustration

IMPORTANT:

Water column pressure of 3.5 inches (8.7 mb) for natural gas dryers and 10.5 inches
(26.1 mb) for L.P. gas is required at the gas valve pressure tap of each dryer for proper
and safe operation.

A 1/8” N.P.T. plugged tap, accessible for a test gauge connection,

must be

installed in the main gas supply line

immediately upstream of each dryer.

IMPORTANT:

Pipe joint compounds that resist the action of natural gas and L.P. gas

must be

used.

WARNING:

Test

ALL

connections for leaks by brushing on a soapy water solution (liquid detergent

works well).

WARNING: NEVER

TEST

FOR

LEAKS

WITH

A

FLAME!!!

«
...
30
31
32
33
34
...
»

Summary of Contents for AD-320





























































Reviews:

No comments

Related manuals for AD-320

Brand: Eaton Pages: 6

Brand: tau Pages: 9

Brand: tau Pages: 8

Brand: Union Instruments Pages: 63

Brand: Sartorius Pages: 165

Brand: SMC Networks Pages: 15

iEP-5000G Series

Brand: ASROCK Pages: 2

Brand: Runxin Pages: 4

Tunnel Master Jr

Brand: ICS Pages: 70

Brand: Colorbeam Pages: 12

Brand: Kramer Pages: 60

Brand: Watt Stopper Pages: 3

SANTOKA 12.1 BX PCT

Brand: Garz & Fricke Pages: 37

Brand: Quick Pages: 16

Brand: ISC Pages: 20

Brand: SUPMEA Pages: 32

Brand: Task Force Tips Pages: 8

Brand: Steren Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands