ADC AD-320 Installation Manual Download Page 31 | Manualshive

Page: 31 / 60

background image

112144 - 46

www.adclaundry.com

27

3. Piping/Connections

ALL

components/materials

must conform

to National Fuel Gas Code Specifications ANSI Z223.1-LATEST

EDITION, or in Canada, CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (Liquid Propane
[L.P.] Gas) or LATEST EDITION (for General Installation and Gas Plumbing), as well as local codes and
ordinances and

must be

done by a qualified professional. It is important that gas pressure regulators meet

applicable pressure requirements, and that gas meters be rated for the total amount of

ALL

the appliance BTUs

being supplied.

The dryer is provided with two (2) 1/2” N.P.T. inlet pipe connections (one [1] for each basket [tumbler]) at the
rear of the dryer. If a separate feed is provided for each basket (tumbler) from the main supply line (header),
then a 1/2” (12.7 mm) line connection is sufficient. However, if the top and bottom basket (tumbler) connections
are connected together, the supply from the header

must be

increased to 3/4-inch (19.05 mm). An optional

piping kit is available from the factory as illustrated below and on

. It is recommended that a gas

shutoff valve be provided to the gas supply line of each dryer for ease in servicing.

TYPICAL GAS CONNECTIONS

IMPORTANT:

When plumbing upper and lower baskets (tumblers) together, as illustrated above,
supply connection

must be

a minimum of 3/4” (19.05 mm).

«
...
29
30
31
32
33
...
»

Summary of Contents for AD-320





























































Reviews:

No comments

Related manuals for AD-320

Leroy-Somer R180

Brand: Nidec Pages: 20

Brand: D-Link Pages: 40

Brand: Panasonic Pages: 15

Brand: Panasonic Pages: 42

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

Brand: Daktronics Pages: 5

Brand: Daikin Pages: 12

Brand: Federal Signal Corporation Pages: 34

Brand: K'Nex Education Pages: 56

Brand: Lamtec Pages: 136

Brand: LAS Pages: 6

Brand: S&P Pages: 12

Brand: S&C Pages: 34

Brand: S&C Pages: 32

IntelliCap Plus

Brand: S&C Pages: 32

Brand: S&P Pages: 12

Brand: S&C Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands