ADB Safegate UEL-1-120 User Manual Download Page 31 | Manualshive

Page: 31 / 42

background image

6.4 How to dismantle the optical assembly

6.4.1 Procedure

The following table instructs you on how to dismantle the optical assembly (to be done in the maintenance base):

1. Remove the optical cartridge (1) from the light.
2. Remove the lamp (2).
3. Slide the front gasket (1a) around the front of the cartridge. This releases the reflector (1c) and the front glass (1b).
4. Reassembly is done in the opposite order.

UM-4020 / AM02-630e, Rev. 2.0, 2020/05/19

25

Copyright

©

ADB Safegate, All Rights Reserved

«
...
29
30
31
32
33
...
»

Summary of Contents for UEL-1-120











































Reviews:

No comments

Related manuals for UEL-1-120

Brand: Raytech Pages: 21

Brand: Teac Pages: 2

Brand: laerdal Pages: 2

Brand: Panlux Pages: 2

Brand: Datex-Ohmeda Pages: 80

Brand: MacDon Pages: 2

Brand: V-TAC Pages: 6

Brand: Idex Pages: 141

Brand: IDEAL Networks Pages: 8

Brand: IDEAL Networks Pages: 5

Brand: EuroLite Pages: 28

Brand: Teac Pages: 9

Brand: Tascam Pages: 3

Brand: Tascam Pages: 56

Portastudio 2488

Brand: Tascam Pages: 28

Brand: Tascam Pages: 2

Brand: Tascam Pages: 5

Brand: Tascam Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands