ADB Safegate RELIANCE L-810 OBSL-L User Manual Download Page 24 | Manualshive

Page: 24 / 34

background image

4.4 Aiming the Photocell

To aim the Photocell:

1. Open the electronics enclosure and loosen the lock nut holding the photocell.
2. Adjust the photocell to the proper direction, (towards the nearest pole) such as, the North Pole.
3. Tighten the lock nut.
4. Close up the electronics enclosure

RELIANCE L-810(L) OBSL-L Steady Burning LED Obstruction Light
Maintenance and Repair

18
Copyright

©

ADB Safegate, All Rights Reserved

«
...
22
23
24
25
26
...
»

Summary of Contents for RELIANCE L-810 OBSL-L



































Reviews:

No comments

Related manuals for RELIANCE L-810 OBSL-L

Brand: ICS Schneider Messtechnik Pages: 124

Brand: Laica Pages: 4

WJHD100 - DIGITAL DISC RECORDE

Brand: Panasonic Pages: 7

Brand: Ocean Sonics Pages: 45

Brand: TC Electronic Pages: 4

Brand: TC Electronic Pages: 6

Brand: TC-Helicon Pages: 12

Brand: TC Electronic Pages: 76

Brand: Ultraflex Pages: 48

Brand: Zero 88 Pages: 12

Brand: Zest4Leisure Pages: 4

Brand: Zeiss Pages: 119

Brand: Zehnder Rittling Pages: 32

Brand: Nady Audio Pages: 2

Brand: AMP Lighting Pages: 5

Brand: Strapack Pages: 16

Brand: Hameg Pages: 60

Brand: Alpina Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands