Adaptive AlphaXpress 8731 Installation And Maintenance Manual Download Page 30

Page: 30 / 56

QUIPMENT

NSIDE

VIEW

AlphaXpress 8731 Sign Installation and Maintenance Manual (pn 1508610601 rev. A)

AC POWER INPUT

AC power attaches to the power supply through this connection.

ADDRESSING PORT

This address is set using an address plug (pn 1509100701).

Note: This connection selects BAUD rate, controls power supply on / off function, and

addressing the power distribution monitor board. Removing the address plug will
turn off the power supply.

COMM PORT

RS422 communications

LD1

AC BAD

On = Indicates the incoming voltage is below 90VAC.

LD2

DC BAD

On = Indicates DC output is below 12.3VDC.

LD3

AC GOOD

On = Indicates the incoming voltage is above 90VAC.

LD4

DC GOOD

On = Indicates DC output is greater than 12.3VDC.

LD5

FAULT

On = PDMB (Power Distribution Monitor Board) detected a power fault condition has
occurred.

LD6

COMM

Flashing = PDMB is receiving communications from the controller on the RS422 bus.

LD7

RUN

Flashing = PDMB processor is running its tasks.

DC POWER OUTPUT

+12VDC is supplied to all connected electronic components.
• V– = Violet wiring
• V+ = Orange wiring

Jumper wires

Refer to the appropriate wiring

diagram for your sign model. These

are preset from the factory with the

correct settings.

Plugs into P3

Summary of Contents for AlphaXpress 8731

























































Search results

Summary of Contents for AlphaXpress 8731

Reviews:

Related manuals for AlphaXpress 8731

Brands by name

Popular brands

Adaptive AlphaXpress 8731, Installation And Maintenance Manual

Search results

Summary of Contents for AlphaXpress 8731

Reviews:

Related manuals for AlphaXpress 8731

Brands by name

Popular brands