Adaptive AlphaXpress 8731 Installation And Maintenance Manual Download Page 6

Page: 6 / 56

NTRODUCTION

ONTROLLER

MEMORY

BATTERY

BACKUP

AlphaXpress 8731 Sign Installation and Maintenance Manual (pn 1508610601 rev. A)

Controller memory battery backup

In the event of a power loss, a lithium battery provides power to the sign controller board(s).

Note:

The backup battery provides only enough power to operate the sign’s controller memory, not the sign’s

LED displays.

3V lithium backup battery

One 3V lithium battery is located on the sign controller board(s).

Figure 1.

A 3V lithium battery is located on the sign controller.

WARNING!

Danger of explosion if battery is incorrectly replaced. Replace only with the same or

equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.

3V lithium battery (Panasonic

CR2032 or equivalent)

Summary of Contents for AlphaXpress 8731

























































Search results

Summary of Contents for AlphaXpress 8731

Reviews:

Related manuals for AlphaXpress 8731

Brands by name

Popular brands

Adaptive AlphaXpress 8731, Installation And Maintenance Manual

Search results

Summary of Contents for AlphaXpress 8731

Reviews:

Related manuals for AlphaXpress 8731

Brands by name

Popular brands