Adaptive AlphaXpress 8731 Installation And Maintenance Manual Download Page 18

Page: 18 / 56

NSTALLATION

LECTRICAL

INSTALLATION

AlphaXpress 8731 Sign Installation and Maintenance Manual (pn 1508610601 rev. A)

Sign to ground controller network connection

Figure 15.

Ground controller communications wiring.

Network wiring conduit

Install two runs of network wire (pn 71240402)

from the ground controller to the sign.

Connect one run to the RS422 terminal block on

the ground controller and to the RS422 terminal

block on the sign’s controller plate (see below).

(The other wire run is a spare in case the first run

ever fails.)

RED - ORANGE/WHITE

BLACK - WHITE/ORANGE

SHIELD

GREEN - BLUE/WHITE

WHITE - WHITE/BLUE

RED

BLACK

SHIELD

GREEN

WHITE

RED

BLACK

SHIELD

GREEN

WHITE

Run network wiring conduit into this area.

If any drilling is required, vacuum any

metal filings from the sign. Otherwise, the
sign fans could blow these pieces around

and possibly damage electronic

components.

RED - ORANGE/WHITE

BLACK - WHITE/ORANGE

SHIELD

GREEN - BLUE/WHITE

WHITE - WHITE/BLUE

Ground controller

(housed in weatherproof

structure near the sign)

Controller plate

Summary of Contents for AlphaXpress 8731

























































Search results

Summary of Contents for AlphaXpress 8731

Reviews:

Related manuals for AlphaXpress 8731

Brands by name

Popular brands

Adaptive AlphaXpress 8731, Installation And Maintenance Manual

Search results

Summary of Contents for AlphaXpress 8731

Reviews:

Related manuals for AlphaXpress 8731

Brands by name

Popular brands