DW7451 Heavy-Duty Table Saw Stand
WARNING:
To reduce the risk of serious personal injury, read the table saw
instruction manual before using any accessory. Failure to heed these warnings may
result in personal injury and serious damage to the table saw and the accessory.
When servicing this tool, use only identical replacement parts.
• This table saw stand is designed only for use with the DW745, DWE7480 and DCS7485
table saws. Do not use this stand with any other tool.
• Do NOT mount the table saw to the stand in any other
orientation.
• Position all of the feet in the same orientation or unstable footing may occur.
• Do not climb on or sit on saw stand.
• Do not use saw stand on inclined, uneven or unstable surfaces.
• Do not use saw stand if it is damaged or bent.
• The back legs of the saw stand are slightly longer than the front legs to provide
additional support. Use the saw stand and operate the table saw from the front side only.
• Maximum load: 150 lbs. (68.1 kg.)
SAVE THESE INSTRUCTIONS
Assembly
• Assemble as shown in Figure A.
To Open the Table Saw Stand
1. Unfold the saw stand until it is fully opened. Place it upright, as shown in Figure B.
2. Place the table saw on the stand. Place the front bar of the saw into the lip
1
on the
front of the stand (Fig. C).
3. Lower the rear feet of the saw onto the ledge
2
at the back of the stand as shown in
Figure C.
4. Secure the rear of the saw with the bolts provided (Fig. D). Be sure the saw does not
rock or wobble in place.
To Close the Stand
1. Remove the bolts from the rear rail of the saw.
2. Tilt the rear of the saw up allowing the rear feet to clear the lip on the back of the
stand.
3. Pull the saw forward and up allowing the front bar to slide out of the lip on the stand.
4. After stowing the saw, pick the stand up by both rails and close it by squeezing the
top rails toward each other.
Fig. A
D
e
WALT
Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (JUL16) Form No. N482036 DW7451 Copyright © 2016
D
e
WALT
The following are trademarks for one or more
D
e
WALT
power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box
configuration; and the array of lozenge-shaped humps on the surface of the tool.
Fig. B
Fig. D
Fig. C
Socle robuste DW7451 pour scie de table
AVERTISSEMENT :
pour réduire le risque de blessures graves, lire le mode d’emploi
de la scie de table avant d’utiliser tout accessoire. Négliger de se conformer à ces
avertissements pourrait se solder par des blessures corporelles et des dommages
importants à la scie de table et à l’accessoire. Pour la réparation de cet outil, n’utiliser
que des pièces de rechange identiques.
• Ce socle pour scie de table est conçu uniquement pour le modèle de scie de table DW745,
DWE7480 et DCS7485. Ne pas utiliser le socle avec tout autre outil.
• Fixer la scie sur le stand que dans l'orientation représentée sur la figure C. NE PAS
assembler la scie de table sur le socle dans une direction différente.
• Positionner tous les pieds du socle dans la même direction pour éviter un déséquilibre.
• Ne pas monter debout ni s’asseoir sur le socle de la scie.
• Ne pas utiliser le socle sur des surfaces inclinées, irrégulières ou instables.
• Ne pas utiliser le socle s’il est endommagé ou plié.
• Les pattes arrières du socle de la scie de table sont légèrement plus longues que celles
du devant pour offrir un soutien supplémentaire. Utiliser le socle et la scie de table
uniquement par l’avant.
• Charge maximale : 68,1 kg (150 lb)
1
2
Final Page size: 8.5 x 11 in
