manualshive.com logo in svg

Adaptec ARO-1130CA, Installation And Hardware Manual, Page: 40 / 78

Share
Download
Adaptec ARO-1130CA Installation And Hardware Manual Download Page 40

4-2

ARO-1130CA Installation and Hardware Guide

Installing the Array1000CA Driver for Windows NT

This section explains how to install the Array1000CA Miniport 
Driver (

cda1000.sys

) for Windows NT. To begin driver installation, 

see either Installing the Driver When Installing Windows NT below, or 
Installing the Driver When Windows NT is Already Installed on 
page 4-3.

Note: 

We recommend that you install your Windows NT 

operating system on an array to take advantage of the per-
formance or redundancy features of the array.

Installing the Driver When Installing Windows NT

To install the 

cda1000.sys

 driver when you are installing Windows 

NT, follow the instructions below.

Note: 

If you have multiple arrays, we recommend tempo-

rarily powering off all devices except for the boot array 
before installing Windows NT; otherwise, Windows NT lim-
its the size of the partitions you can create to 1 GByte. When 
Windows NT installation is complete, power on all devices 
and reboot the system.

Windows NT 4.0 Installation

To install the 

cda1000.sys

 driver when you are installing Windows 

NT 4.0, follow these steps:

1

Start your system with the Windows NT Boot Diskette in the 
floppy disk drive or the Windows NT Boot CD-ROM in the 
CD-ROM drive.

2

Boot diskette installation: When prompted, insert diskette #2 in 
your floppy drive. After a few moments you will see a blue 
screen. To setup Windows NT now, press Enter and continue 
with Step 3 below.

Boot CD-ROM installation: When the following message 
appears onscreen, press the F6 key and skip to Step 4 below.

Setup is inspecting your computer’s hardware…

Summary of Contents for ARO-1130CA















































































Reviews:

No comments