manualshive.com logo in svg

Adaptec ARO-1130CA, Installation And Hardware Manual, Page: 22 / 78

Share
Download
Adaptec ARO-1130CA Installation And Hardware Manual Download Page 22

2-8

ARO-1130CA Installation and Hardware Guide

4

Attach the remaining connectors on the cable to the remaining 
internal devices.

5

Connect an available DC power cable (from your computer’s 
power supply) to the power input connector on each SCSI 
device.

Connecting External SCSI Devices

To install external SCSI devices, you will first need to install an inter-
nal-to-external SCSI port expansion kit. The kit usually consists of a 
special cable that converts the internal SCSI connector on the mother-
board to an external SCSI connector on the chassis of your computer. 
Refer to the expansion kit documentation for installation instructions. 
Figure 2-6 shows a typical installation of a 68-pin Ultra Wide internal-
to-external cable.

Figure 2-6. Installing an Internal-to-External SCSI Port Expansion Cable

68-Pin Ultra Wide 
External SCSI 
Connector

68-Pin Ultra Wide 
Internal-to-External 
SCSI Cable

68-Pin Ultra Wide 
Internal SCSI 
Connector

Summary of Contents for ARO-1130CA















































































Reviews:

No comments