Adam Equipment pgw 1502e User Manual Download Page 15 | Manualshive

Page: 15 / 48

background image

Page 15 of 48

17 NEWTONS

N

All

0.00980665

101.971623

18 CUSTOM

Custom

All

As specified

As specified

It is possible to set the balance to display only grams. Grams will always be
one of the units enabled, by default.

If “CUSTOM” unit is selected, the balance will prompt for entering a multiplier
by displaying “MULTIPLIER XX,XXX”, where “XX,XXX” is the last stored
value. Any value ranging from 0.100 to 10.000 may be entered, by which the
weight in grams will be multiplied before being displayed. If a multiplier of
greater than 1.000 is entered, the number of decimal places displayed will be
reduced by one. This multiplier value will be saved for the next use till it is
changed by the user.

The balance displays the alternate weighing units with as much precision as
possible. For example, the 450g x 0.001g balance could weigh up to:

Unit

Maximum

d =

g. 450g

0.001g

mg 450000

1

kg 0.450000 0.000001
ct. 2250

0.005

dwt 289.356

0.001

GN 6944.52

0.02

ozt 14.86780  0.00005
oz 15.87325  0.00005
lb 0.99207  0.00001
dr 253.972  0.001
tl.T 12.00000  0.00005
tl.H 12.02275  0.00005
tl.S 11.90415  0.00005
MM 119.9995  0.0005
T 38.5808  0.0001
ti 27.5577  0.0001
N 4.4130

0.0001

9.4 FUNCTIONS

When weighing, the user can access the applications that have been enabled
(see section 13.2).

The following applications are available in this version (2.41):

•

Weighing

•

Parts counting

•

Percent weighing

•

Check weighing

•

Animal / dynamic weighing

•

Net/Total

•

Density determination

The selectable functions can be enabled using a similar method to the Units
above by turning the functions on or off.

© Adam Equipment Company 2007

«
...
13
14
15
16
17
...
»

Summary of Contents for pgw 1502e

















































Reviews:

No comments

Related manuals for pgw 1502e

Brand: Hardy Process Solutions Pages: 18

Brand: OHAUS Pages: 5

Brand: RADWAG Pages: 16

Brand: DCOOK Pages: 28

Brand: T Scale Pages: 49

Brand: Orbegozo Pages: 23

Brand: Soehnle Professional Pages: 86

Brand: A&D Pages: 47

Brand: MRC Pages: 81

Brand: ProMed Pages: 112

Precision Elite Series

Brand: Lyman Pages: 4

Brand: Menuett Pages: 13

Brand: Tanita Pages: 23

Brand: Tanita Pages: 28

Brand: Terraillon Pages: 12

Brand: Terraillon Pages: 17

Brand: Monzana Pages: 16

Brand: Avery Berkel Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands