background image

eWON4001™

Installation Guide

ver 2.1

page 4 of 31

 2 Structure of the eWON technical documentation 

The eWON technical documentation is structured in 4 different levels as shown in the table below:

All those manuals are available for download in pdf format on the eWON website: 

http://www.ewon.biz

.

Level

Title

Contents

1

Hardware

Installation Guide

(the present document)
(~40pp)

Detailed description of the hardware platform, 
of its interfaces, available options and 
accessories. Hardware specifications, 
conformity to standards. Installation 
recommendations and pinout of the 
connectors. Step-by-step tutorial to establish 
first communications and make the IP 
configuration. 
Exists for the following platforms: 

• 

 

eWON2000/4000

• eWON1000
• eWON500, 2001, 4001

2

Software

Getting Started

(~30pp)

Manual to start using the basic functions of the 
eWON software. Covers most usual 
applications (eWON 4000 only).

3

Software

User Manuals

(~250pp)

Exhaustive manual to use all advanced 
functions of the eWON. Contains BASIC and 
HTML syntax.
(Exists for all platforms)

4

Application Notes
Technical Notes

• 

 

Unitelway topology Gateway XIP

• Unitelway for Schneider PLC, 
• Gateway MPI for Siemens PLC and 

Gateway for IP devices

• Etc, etc.

Table 3: eWON technical documentation different levels

Summary of Contents for eWON4001



































Reviews: