P218703
ADt 001 M
B
© 2021 « Any reproduction of this document whether total or partial without the written consent of ACTIA Automotive is forbidden”
Page 33 sur 37
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules and with ISED license-exempt RSS standard(s).
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Part 15.19 Warning Statement
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notes (ISED):
(EN) This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
(FR) Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210. Son
fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interférence et
(2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son
fonctionnement.
(EN) Radio frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Innovation, Science and Economic Development
Canada (ISED) radio frequency exposure limits. The Wireless Device should be used in such a manner such that
the potential for human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with the ISED RF Exposure limits under mobile
exposure conditions. (antennas at least 20cm from a person‘s body).
(FR) Informations concernant l'exposition aux fréquences radio (RF)
La puissance de sortie émise par l'appareil de sans fiIs est inférieure à la limite d'exposition aux fréquences radio
d‘Innovation, Sciences et Développement économique Canada (ISDE). Utilisez l'appareil de sans fil de façon à
minimiser les contacts humains lors du fonctionnement normal.
Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'IC dans des
conditions d'exposition à des appareils mobiles (les antennes se situent à moins de 20cm du corps d'une
personne).
VIII.2
D
ANGEROUS GOODS TRANSPORTATION REGULATION
(ATEX):
TGU-R ACCESS is not compliant to dangerous good transportation regulation (ATEX) with internal optional
battery pack and/or RTC coin cell options mounted.
When powered after vehicle master switch and without internal battery option and RTC coin cell (meaning no
more power source inside and outside the TGUR ACCESS product during vehicle loading and unloading
operation), the TGU-R ACCESS is not subject to dangerous good transportation regulation (ATEX).
A variant must then be created to comply with ATEX regulation.
IX
AFTER SALES
IX.1
ECU
REPLACEMENT
No item of equipment in a system will be replaced without prior testing with a diagnostic tool. This is to avoid the
exchange of products that are operating correctly but connected via a faulty contact, for example.
Replacement products must comply with the manufacturer’s specifications.
The ECU replacement must be done when the battery is switched off.
