background image

20 

 

 

Warranty Certificate 

 

The  specifications  within  this  document  are  provided  for  information 
purposes only and are under no circumstances binding. 
 
With  the  aim  of  constantly  improving  our  products,  all  modifications 
considered necessary may be made without notice. 
This manual is correct at time of printing.  
 
Our appliances are guaranteed against faults and hidden defects subject 
to the following conditions: 
 

 

The  appliance  must  have  been  installed  by  a  registered  competent 
installer (HETAS) or inspected by local authority Building Control. 

 

The appliance must be installed and operated in accordance with our 
instruction manual. 

 

The guarantee is for a period of 5 years on the appliance body from the 
date of purchase. 

 
The  following  components  are  considered  as  consumables  and  are 
excluded from the guarantee: 
 

 

Grates  

 

Rope seals 

 

Ashpan  

 

Internal vermiculite panels  

 

Glass  

 

Baffle plates 

 
Your statutory rights are not affected by this warranty. 
 
 

In the event of a warranty claim, please return the form overleaf to  

ACR Heat Products Ltd, Unit One, Weston Works, Weston Lane, Tyseley, 

Birmingham, B11 3RP, UK. 

Summary of Contents for MV2CL






















Reviews: