Acorp Sprinter W422G User Manual Download Page 44 | Manualshive

Page: 44 / 81

background image

44

Fields in this page:

Field

Description

IGMP Proxy

Enable/disable IGMP proxy feature

Proxy Interface

The upstream WAN interface is selected here.

Function buttons in this page:

Apply Changes

Click to save the setting to the configuration.

Undo

Discard your settings.

«
...
42
43
44
45
46
...
»

Summary of Contents for Sprinter W422G


















































































Reviews:

No comments

Related manuals for Sprinter W422G

Brand: ZETR Pages: 2

Brand: CallDirect Pages: 33

Brand: LaCie Pages: 44

LaCie Ethernet Disk

Brand: LaCie Pages: 2

5big - Network NAS Server

Brand: LaCie Pages: 9

Brand: LaCie Pages: 14

12big Rack Fibre 8

Brand: LaCie Pages: 9

Brand: National Instruments Pages: 34

Brand: Zonet Pages: 10

Brand: Samsung Pages: 65

Brand: Tripp Lite Pages: 20

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

totalstorage 200

Brand: IBM Pages: 180

MultiConnect SE MTS2EA

Brand: Multitech Pages: 2

Fieldpoint cFP-RTD-124

Brand: National Instruments Pages: 15

Brand: VCS Pages: 118

Brand: Juniper Pages: 2

Brand: IBASE Technology Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands