background image

MANUFACTURER’S LIMITED WARRANTY

Agri-Cover, Inc. extends the following one (1) year Limited Warranty for the ADARAC™ Truck 

Bed Rack, ADARAC™ Aluminum M-Series, ADARAC™ Aluminum Series, ADARAC™ 

Aluminum Pro Series and ADARAC™ Rail and Upright Kits:

Agri-Cover, Inc. warrants for a period of one (1) year from the date of manufacture that 

its ADARAC™ Truck Bed Rack, ADARAC™ Aluminum M-Series, ADARAC™ Aluminum 

Series, ADARAC™ Aluminum Pro Series and ADARAC™ Rail and Upright Kits are free 

from defects in workmanship, under normal use for the vehicle model it was intended 

for. This Limited Warranty does not cover any damage due to accident, abuse, misuse, 

alteration, neglect, improper installation, or ordinary wear and tear.

Agri-Cover, Inc.’s sole obligation under this Limited Warranty is limited to the repair or 

replacement, at its option, of defective parts only. No labor or service allowance is given 

or implied. IN NO EVENT SHALL AGRI-COVER, INC. BE LIABLE FOR INCIDENTAL, 

CONSEQUENTIAL, OR SPECIAL DAMAGES. AGRI-COVER, INC. EXPRESSLY 

DISCLAIMS ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND 

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE LIMITED WARRANTY 

DESCRIPTION CONTAINED HEREIN.

For warranty, fi ll out the warranty claim form at www.agricover.com/warrantyclaim or call 

our Customer Service Department at 866-630-8726 to determine if only a replacement 

part is needed or if the rack needs to be returned for inspection and repair. Goods to be 

returned must have a pre-authorized RA # (Return Authorization Number) - obtained by 

calling the number above. Mark the number on the package and ship it freight prepaid to 

address below. Agri-Cover, Inc. will pay freight to return goods to sender.

This Limited Warranty gives you specifi c legal rights and you may have other rights, which 

vary, from state to state.

For replacement parts, shop at adaracparts.com or call Customer Service at

866-630-8726.

032420   2000117_I

Hours: 8:00 am - 5:00 pm CST Monday through Friday, except Holidays

Agri-Cover, Inc.

Customer Service Dept

3000 Hwy 281 SE

Jamestown, ND 58401

Phone: 866-630-8726

© 2020 AGRI-COVER, INC. ALL RIGHTS RESERVED.

Product subject to change without notice. Patents: agricover.com/patents. 

Summary of Contents for ADARAC Aluminum M Series

















Reviews: