Acer Aspire M3985 Service Manual Download Page 26

Page: 26 / 126

Chapter 2

Advanced Chipset Configuration

Intel EIST

When enabled, this feature allows the OS to reduce power consumption.
When disabled, the system operates at maximum CPU speed.

Enabled

Disabled

Intel XD Bit

When enabled, the processor disables code execution when a worm
attempts to insert a code in the buffer preventing damage and worm
propagation.

When disabled, the processor forces the Execute Disable (XD) Bit feature
flag to always return to 0.

Enabled

Disabled

Intel VT

Enables or disables the Virtualization Technology (VT) availability. If
enabled, a virtual machine manager (VMM) can utilize the additional
hardware virtualization capabilities provided by this technology.

Note

: A full reset is required to change the setting.

Enabled

Disabled

Summary of Contents for Aspire M3985































































































































Search results

Summary of Contents for Aspire M3985

Reviews:

Related manuals for Aspire M3985

Brands by name

Popular brands

Acer Aspire M3985, Service Manual

Search results

Summary of Contents for Aspire M3985

Reviews:

Related manuals for Aspire M3985

Brands by name

Popular brands