manualshive.com logo in svg

Acer Aspire AM3610, Service Manual

Share
Download
Acer Aspire AM3610 Service Manual Download Page 7

Chapter 1

1

Overview

Size

•

Max. 244 mm x 244 mm, MicroATX

Processor

•

Socket type: Intel

®

 socket T LGA775 pin

•

Socket quantity: one

•

Processor type: Intel

®

 Celeron/ Celeron D/ Pentium 4/ Pentium D/ Core 2 Duo/ Core 2 Extreme/

Quad Core, core speed 533/ 800/ 1066 MHz

System Chipset

•

North bridge: ATI RS600

•

South bridge: ATI SB600

•

Super I/O: ITE8718

Memory

•

Four DDR2 sockets

•

DDR2 400/ 533/ 667/ 800 SDRAM support

•

256MB/ 512MB/ 1GB/ 2GB DDR2 DIMMs support

•

Up to 8GB system memory support

•

Dual channel function enabled when plugging in two same memory size DDR2 memory modules

Onboard Graphics Solution

•

ATI RS600 on-die graphic solution (ATI Radeon

®

 X700-based graphic core)

•

ATI AVIVO technology support

•

Multiple display features support

•

One D-Sub VGA port on the rear side

•

One HDMI port on the rear side (A14)

•

SDVO interface which supports hot plug detection

HDMI

•

With HDCP solution

•

Meets HDMI 1.2a specification

PCI Express/PCI Slots

•

One PCI Express x16 slot

•

One PCI Express x1 slot

•

Two PCI slots

Floppy Disk Drive

•

One slot, 1.44MB/3 mode 3.5” devices support

System Specifications

Chapter 1

 

Summary of Contents for Aspire AM3610


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands