manualshive.com logo in svg

Acer Aspire AM3610, Service Manual

Share
Download
Acer Aspire AM3610 Service Manual Download Page 25

Chapter 1

19

Super I/O

USB Interface

Item

Description

Chip

ITE IT8718F

Feature

•  Low pin count interface
•  Serial flash I/F for BIOS
•  Consumer remote control (TV remote) IR with power-up feature
•  8-pin VID
•  SST interface
•  PECI interface (host)
•  Multi curve for one fan control
•  Multi sensor for one fan control
•  New PCIRST circuit
•  PC98/99/2001, ACPI and LANDesk compliant
•  Enhanced hardware monitor
•  Fan speed controller
•  SmartGuardian controller
•  5V power supply
•  Two 16C550 UARTs
•  Floppy disk controller
•  IEEE 1284 parallel port
•  Keyboard controller
•  48 general purpose I/O pins
•  Watchdog timer
•  ITE innovative automatic power-failure resume and power button 

debounce

•  Serial IRQ support
•  Vbat and Vcch support
•  5V power supply
•  128-pin QFP

Item

Description

Chip

ATI SB600

Feature

•  Five OHCI and one EHCI host controllers to support ten ports
•  Three 2*5 onboard headers

• Four ports for front daughter board
• Two ports for internal USB card IR module

•  Compliant to standard Intel FPIO pin definition
•  USB 2.0/1.1 support

 

Summary of Contents for Aspire AM3610


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands