Acer Altos S300 User Manual Download

Page: 10 / 78

Dual CSM configuration

Dual concentrator services modules

Join/Split bus jumper

Powering on the Altos S300 series enclosure

Altos S300 series jumper settings

Powering on an AC enclosure

4 System monitoring

Overview

Environmental status (ES) block

Features

Alarm buzzer mute

Enclosure front panel LEDs

Disk drive carrier LEDs

Power supply LEDs

Advanced cooling module (ACM) LEDs

5 Installing and removing components

Location of the Components

Installing and removing a disk drive carrier

Installing a disk drive carrier

Removing a disk drive carrier

Installing and removing a power supply

Installing a Power Supply

Removing a Power Supply

Installing and removing an advanced cooling module (ACM)51

Installing an advanced cooling module (ACM)

Removing an advanced cooling module (ACM)

Installing and removing an I/O option module

Installing an I/O option module

Removing an I/O option module

Appendix A: Technical specifications

Appendix B: Safety statements

Index

Summary of Contents for Altos S300















































































Search results

Summary of Contents for Altos S300

Reviews:

Related manuals for Altos S300

Brands by name

Popular brands

Acer Altos S300, User Manual

Search results

Summary of Contents for Altos S300

Reviews:

Related manuals for Altos S300

Brands by name

Popular brands