Acer Altos S300 User Manual Download

Page: 60 / 78

5 Installing and removing components

Installing and removing a power
supply

The power supplies are located in the rear of the enclosure. Follow
these procedures to install and remove the power supplies.

Installing a Power Supply

Select the power supply slot into which the power supply is to be
inserted.

Orient the power supply, such that the LEDs are on the right.

Gently slide the power supply into the empty power supply slot.

Secure in place using the two fixing screws (torque setting 0.3Nm).

Install the power cable into the power connector.

Removing a Power Supply

Turn off the power supply using the switch located on the power
supply unit, and remove the power cable.

Loosen the two fixing screws.

Using the power supply handle, gently slide it out of the enclosure.

Caution:

Immediately replace the power supply carrier after

removal to maintain correct airflow.

ON/OFF
Switch

Handle

AC
Inlet

Summary of Contents for Altos S300















































































Search results

Summary of Contents for Altos S300

Reviews:

Related manuals for Altos S300

Brands by name

Popular brands

Acer Altos S300, User Manual

Search results

Summary of Contents for Altos S300

Reviews:

Related manuals for Altos S300

Brands by name

Popular brands