Acdeos AR FL 210-8/2 Manual Download Page 9 | Manualshive

Page: 9 / 38

background image

AXS

–

Ramp Manual

AXS FL RAMP Manual rev 1

8

Finally remove the wooden and steel
transportation distance pieces.

Check if the Feet assembly is
standing strait under 90 with the floor.
If not tighten or loose the M10
fixations bolts

Ramp stop / Ramp Anti rattling device.
You  will also  need  to  install the ramp stop  at the
door  to  prevent  the  ramp  for  rattling  or  hitting
against the rear door/window. `
We  recommend  positioning  this  as  high  as
possible at the door

The bracket needs to be fitted with the
two  rivet  nuts  M8.  (Drill  Ø11  mm
holes).
Position the bracket so that the rubber
aligns with the rail of the ramp.

Place brackets left and right

Adjust the brackets so the ramp is
held tight when the door is closed.

«
...
7
8
9
10
11
...
»

Summary of Contents for AR FL 210-8/2







































Reviews:

No comments

Related manuals for AR FL 210-8/2

Brand: Hama Pages: 10

Brand: IFO Pages: 8

Brand: Warrior Products Pages: 2

Brand: Navibe Pages: 8

Brand: 4 tec SENSORTECHNOLOGY Pages: 5

Brand: Nauticam Pages: 22

Brand: F&F Pages: 8

Brand: Freefly Pages: 8

Brand: A.MENARINI Pages: 58

Brand: Olympus Pages: 41

Brand: Whispbar Pages: 17

Brand: felisa Pages: 11

Brand: Napoleon Pages: 2

Brand: Skoda Pages: 281

Brand: Velleman Pages: 8

Brand: v.LOGiC Pages: 22

Brand: AFX Pages: 52

Elite Series DBv-CK-LP TO NG

Brand: Lennox Hearth Products Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands