MP5032-2104
XLR8 HEATED PLATEN
16
3.0 REMOVAL AND REPLACEMENT OF PARTS
3.1 CONTROL BOARD
1. Power unit down and unplug from receptacle.
2. Low platen assembly so it is level with the griddle and secure it to griddle.
3. Access control interior by loosening two truss head screws, one at front of control box and one
at rear (Item 18, Circled in , .)
4. Carefully lift the control box cover up, do not stretch the wires attached the the underside of
the cover.
Unless otherwise specified,
Dimensions: Inches
Bends: 90
Tolerances:
Angular 1°
2 Place Decimal .02
3 Place Decimal .005
T.I.R .005
√125 Micro Inches
GD&T Per ANSI Y14.5M
INDICATED EDGES
MUST BE SOFTENED:
* = NEAR SIDE
* = FAR SIDE
* = BOTH SIDES
5
6
1
7
9
4
10
12
16
2
1
2
3
15 4
12
13
3
DEV002214-1
3.
?
18
20
21
17
FRONT
12 LABEL AS #3
12
LABEL AS #2
12
LABEL AS #1
22
22
22
LABEL TERMINAL
END AS #2
LABEL TERMINAL
END AS #4
LABEL TERMINAL
END AS #6
23
23
23
LABEL TERMINAL
END AS #1
LABEL TERMINAL
END AS #3
LABEL TERMINAL
END AS #5
NOTES:
1
TORQUE HEX NUT, ITEM 7 TO 37+/-3 IN-LBS, STARTING IN THE CENTER
AND WORKING FIRST TO THE SIDES AND THEN TO THE ENDS. TIGHTEN
TWICE IN THIS MANNER.
2
APPLY THERMAL JOINT COMPOUND, ITEM 14 ONTO HEATER ITEM 2 ,
USING PASTE APPLICATION STENCIL (#NPT-FIX-TEMP-00046).
3
APPLY THERMAL JOINT COMPOUND, ITEM 14 ONTO THE BOTTOM OF
OVERTEMP, ITEM 10 COMPLETELY AND EVENLY COVERING THE BOTTOM.
4
APPLY THREAD LOCKER, ITEM 15 ON THREADS.
ECN
REV
DESCRIPTION
DATE
APPR
REVISIONS
-01
RELEASED TO PROTOTYPE
08-25-2020
RRR
DEV002214-1
PART NUMBER
Revision
ITEM
DESCRIPTION
3
AT0E-2699-3
E+
23
TERMINAL, QDISC, INSULATED FEM - 14-16AWG .250 X .032 TAB
3
AT0E-2684-2
A02
22
QD TERMINAL MALE INSULATED 14-16 AWG .250 x .032 TAB
4
AT0F-1052-23000
G07
21
WASHER #6 TYPE B PLAIN
4
DEV002324-1
-01
20
PLATE, LOCK, PLATEN
2
AT0F-2691-41001
D01
19
NUT, #10-24 NYLOC
2
AT0F-1046-41060
-+
18
#10-24 X 3/4 TRUSS HEAD
4
AT0F-2691-21001
D01
17
NUT, #6-32 NYLOC
2
AT2I-6065-1
-04
16
INSULATION, UPPER PLATEN
8
AT0F-1046-31030
A01+
15
SCREW, #8-32 x 3/8 PHLP TRUSS HEAD
AR
AT0H-3412-1
B
14
THERMAL JOINT COMPOUND
2
AT2I-5787-1
-04
13
INSULATION, UPPER PLATEN
1
DEV002245-8
-01
12
HARNESS ASSY, XLR8
3
AT0E-6033-1
-06
12
SENSOR, REPLACEABLE RTD
6
AT0F-2755-21030
D01
10
SCREW, #6-32UNC x 3/8 PHILIPS ROUND HEAD MACHINE
6
AT0F-2666-21000
B01
9
WASHER, SS #6 EXTERNAL TOOTH LOCK
AR
AT0H-3065-4
B02
8
THREAD LOCKER 272
18
AT0F-3401-1
-
7
NUT, SPECIAL LOCKING 1/4-20UNC-2B
18
AT0F-1052-51000
G07
6
WASHER 1/4 TYPE B PLAIN STAINLESS STEEL
18
AT0F-2663-4
B02
5
WASHER, Ø.687 OD BELLEVILLE
3
AT1E-2653-5
H+
4
OVERTEMP SWITCH
1
DEV002215-1
-01
3
COVER ASSY, HEATER
3
AT0E-4649-2
-01
2
HEATER. IN-CAST
1
DEV002211-1
-01
1
PLATE ASSEMBLY, HEATER
F
G
J
B
Friday, November 20, 2020 7:24:28 AM
11
5
3
9
2
7
D
12
10
8
6
4
1
4
6
8
10
12
7
2
9
3
5
11
A
C
E
H
K
K
H
E
C
A
D
B
J
G
F
-02
HEATER ASSEMBLY
RRR
11/10/20
N/A
11/10/20
Comments:
Material:
Finish:
N/A
Do Not Scale Drawing
Proj. Engr.
GLS
GLS
Checked
Drawn
08/25/20
Date
Name
AccuTemp Products, Inc.
8415 N. Clinton Park
Fort Wayne, IN 46825
DEV002214
Size: Drawing No.:
Rev:
Title:
D
Sheet 1 of 1
Scale: 1:3
ECN:
5. Turn the control box cover over to access the control board cover.
6. Remove the 2 nuts securing the control board cover, top left and bottom right.
7. Slide the control board cover up and away.
8. Remove wires from the control board, taking note of there original location.
9. Remove control board.
10. Replace with new part and reassemble in reverse order.
11. Ensure control programming is set according to customer wishes