Accurist 0S10 Setting Instructions Manual Download Page 19

Page: 19 / 106

CP00 Operating Instructions continued . . .

Troubleshooting continued . . .

The watch malfunctions in some way and the above procedures do not work.
1.

Press the lower right button until the mode indicator hand points to TME.

Pull the lower right button out one click. Press the other three buttons down

simultaneously for three seconds and release. You will see 8’s on the digital display.

Press the upper left button. You will see UTC on the top half of the digital display.

Press the upper right button to advance the hands of the top dial to the straight up
24-hour position. Use the lower left button to go in reverse.

Press the upper left button. You will see HR on the top half of the digital display.

Press the upper right button to advance the hour and 24-hour hand clockwise until
they both point straight up at the 24-hour position. Use the lower left button to move
the hand anti-clockwise.

Summary of Contents for 0S10











































































































Search results

Summary of Contents for 0S10

Reviews:

Related manuals for 0S10

Brands by name

Popular brands

Accurist 0S10, Setting Instructions Manual

Search results

Summary of Contents for 0S10

Reviews:

Related manuals for 0S10

Brands by name

Popular brands