Accurist 0S10 Setting Instructions Manual Download Page 13

Page: 13 / 106

CP00 Operating Instructions continued . . .

To set the alarms
1.

Push the bottom right hand button until the mode hand indicator points to

AL1, AL2 or AL3.

Press and hold the upper left button for three seconds. The hour and minute

hand will retract to the 12 O’clock position.

Select the time zone on the digital display by pressing the upper right button

or the lower left button.

Pull the lower right button out one click. You will see ON or OFF flashing on

the digital display. Press the lower left button to turn the alarm on or off.

Press the upper right button. You will see the hours flashing. Press the lower

left button to change the hour.

Press the upper right button. You will see the minutes flashing. Press the lower

left button to change the minutes.

Push the lower right button back in one click.

Summary of Contents for 0S10











































































































Search results

Summary of Contents for 0S10

Reviews:

Related manuals for 0S10

Brands by name

Popular brands

Accurist 0S10, Setting Instructions Manual

Search results

Summary of Contents for 0S10

Reviews:

Related manuals for 0S10

Brands by name

Popular brands